Engine Parts Turbo Ec700b D16e Turbocharger For Excavator Spare
Parts
Product parameters
Product Name | Turbocharger Assy |
Appliion | Excavator |
Part Number | 4031133 |
Condition | China OEM |
Engine Brand | VOLVO |
Engine Model | D16E |
Product Type | Engine Turbocharger Assy |
turbocharger | high quality |
Our main products :
* Excavator cylinder seal kits and O-ring kit/box of various
machines . (HYD-SEAL ( Boom, Arm, Bucket )seal kit, Control Valve
Seal Kit, Hyd-Mail seal Kit, Chain adjust seal kit, Swivel joint
seal kit, Swing motor seal kit etc)
* Coupling.(4A 4AS 8A 8AS 16A 16AS 22A 22AS 25A 25AS S29S 28A 28AS
30A 30AS 140A 140AS E300B16T SH160 E200B14T 50AC 50AM E200B12T
E330C 25H 30H 35H 40H 45H 50H 90H 110H 140H 160H)
* Engine parts .( Liner kits,,Pistons,Liners,Gasket
kit,Turbocharger ,Starter motor
Crankshaft,Alternator,Gear/Oil/Water/Feed pumps ,ect,.)
* Pump assy .( K3V63/120/140/180DT,GM06/07/08/09)
* All gears of travel and swing box.(MOTOR SHAFT/CRANKSHAFT,SHAFT
PINION ,CARRIER ASSY ,SUN SHAFT ,PLANET GEAR ,PIN ,NEEDLE
BEARING,COVER,FLANGE HOLDER,MOTOR CASING,RV GEAR SET (A+B),RING
GEAR+HUB)
* Undercarriage parts (china link,idler,track roller,carrier
roller,sprocket,bucket,teeth and seat ect,.)
Notes
Since the turbocharger is often in high-speed, high-temperature
work, the temperature of the turbocharger exhaust gas turbine end
is about 600 °C, and the turbocharger rotor rotates at a high speed
of 8000-11000r/min, so in order to ensure the normal operation of
the supercharger, the following points should be paid attention to
in use:
Don't just leave in the car
After the engine is started, especially in winter, it should be
left to idle for a period of time so that the oil can fully lubrie
the bearings before the supercharger rotor runs at high speed.
Therefore, you must not slam the throttle after just starting to
prevent damage to the supercharger oil seal.
Do not turn off immediately
After a long period of high-speed operation, the engine cannot be
turned off immediately. When the engine is working, a part of the
oil is supplied to the turbocharger rotor bearings for lubriion and
cooling. After the sudden shutdown of the running engine, the oil
pressure drops rapidly to zero, the high temperature of the
turbocharger turbine part is transmitted to the middle, and the
heat in the bearing support shell cannot be quickly taken away, and
at the same time the supercharger rotor is still rotating at high
speed under the action of inertia, so if the engine is suddenly
stopped in the hot engine state, it will cause the oil trapped in
the turbocharger to overheat and damage the bearing and shaft. In
particular, it is necessary to prevent the sudden flameout after
slamming the throttle a few times.
Keep it clean
When disassembling the supercharger, it is necessary to keep it
clean, and each pipe joint must be blocked with a clean cloth to
prevent debris from falling into the supercharger and damaging the
rotor. When repairing, care should be taken not to damage the
impeller by collision, and if the impeller needs to be replaced,
the dynamic balance test should be done. After reloading, remove
the blockage.
To be cleaned
Since the supercharger is often operated at high temperature, its
lubriing oil pipeline is easily partially coking due to high
temperature, which will cause insufficient lubriion of the
supercharger bearing and damage. Therefore, the lube oil line is
cleaned after a period of operation.
Pay attention to maintenance
Before leaving the car and after receiving the car, the connection
of each tube of the airway should be checked to prevent loosening
and falling off and causing the supercharger to fail and the air
short circuit into the cylinder.
It can be seen that after the engine is supercharged, the structure
of the parts has been strengthened, and from the aspect of use and
maintenance, it is necessary to strengthen the mandatory
maintenance of the engine and pay attention to the correct
operation method.
FAQ
Q1. What parts you have?
A:We are specialized in the excavator spare parts, such as
electrical parts,rubber series,pressure sensor series,valve
series,mini parts,wearing parts and so on. If you have a lot of
products to customize, we can also produce them.
Q2. How will you guarantee the quality?
We will test and send testing video to buyer confirm before
shipping.
Q3. If i don't have part number, can you check for me?
A: Yes, If possible, you can send us pictures of old products,
nameplate or the size for reference.
Q4: What is the warranty of the parts after I purchased?
A: The warranty is 6/12 Months based on the item details. For
natural broken, 3 months. Guarantee genuine parts.
Q5. When will get the items after I place order?
Once your payment is confirmed, we will arrange the goods within 24
hours; if not in stock , we will inform you before placing the
order.
